Pass Cisco Certified Design Associate 100-105 certification exam with high grades in the very first attempt. Now no worries of wasting your time and money because BrainDumps-VCE has offered the best 100-105 certification exam dumps material for guaranteed success. The 100-105 exam dumps material is detailed and involves all the aspects to make the success confirm. The best quality and authenticity of the 100-105 certification exam dumps is used by more than 70,000 professionals worldwide.
100-105 exam questions, 100-105 PDF dumps; 100-105 exam dumps:: https://www.dumpsschool.com/100-105-exam-dumps.html (347 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)
Latest and Most Accurate Cisco 100-105 Dumps Exam Questions and Answers:
To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.)
A. R2(config-if)#clock rate
C. R2(config-if)#ip ospf cost
D. R2(config-if)#ip ospf priority
E. R2(config-router)#distance ospf
Answer: B, C
The cost (also called metric) of an interface in OSPF is an indication of the overhead required to send packets across a certain interface. The cost of an interface is inversely proportional to the bandwidth of that interface. A higher bandwidth indicates a lower cost. There is more overhead (higher cost) and time delays involved in crossing a 56k serial line than crossing a 10M Ethernet line. The formula used to calculate the cost is:
Cost = 10000 0000/bandwidth in bps
For example, it will cost 10 EXP8/10 EXP7 = 10 to cross a 10M Ethernet line and will cost 10 EXP8/1544000 =64 to cross a T1 line.
By default, the cost of an interface is calculated based on the bandwidth; you can force the cost of an interface with the ip ospf cost interface subconfiguration mode command.
After the network has converged, what type of messaging, if any, occurs between R3 and R4?
A. No messages are exchanged
B. Hellos are sent every 10 seconds.
C. The full database from each router is sent every 30 seconds.
D. The routing table from each router is sent every 60 seconds.
HELLO messages are used to maintain adjacent neighbors so even when the network is converged, hellos are still exchanged. On broadcast and point-to-point links, the default is 10 seconds, on NBMA the default is 30 seconds.
Although OSPF is a link-state protocol the full database from each router is sent every 30 minutes (not seconds) therefore, C and D are not correct.
Which OSI layer header contains the address of a destination host that is on another network?
E. data link
Only network address contains this information. To transmit the packets the sender uses network address and datalink address. But the layer 2 address represents just the address of the next hop device on the way to the sender. It is changed on each hop. Network address remains the same.
Which layer of the TCP/IP stack combines the OSI model physical and data link layers?
A. Internet layer
B. transport layer
C. application layer
D. network access layer
The Internet Protocol Suite, TCP/IP, is a suite of protocols used for communication over the internet. The TCP/ IP model was created after the OSI 7 layer model for two major reasons. First, the foundation of the Internet was built using the TCP/IP suite and through the spread of the World Wide Web and Internet, TCP/IP has been preferred. Second, a project researched by the Department of Defense (DOD) consisted of creating the TCP/IP protocols. The DOD’s goal was to bring international standards which could not be met by the OSI model.
Since the DOD was the largest software consumer and they preferred the TCP/IP suite, most vendors used this model rather than the OSI. Below is a side by side comparison of the TCP/IP and OSI models.
Which protocol uses a connection-oriented service to deliver files between end systems?
TCP is an example of a connection-oriented protocol. It requires a logical connection to be established between the two processes before data is exchanged. The connection must be maintained during the entire time that communication is taking place, then released afterwards. The process is much like a telephone call, where a virtual circuit is established–the caller must know the person’s telephone number and the phone must be answered–before the message can be delivered.
TCP/IP is also a connection-oriented transport with orderly release. With orderly release, any data remaining in the buffer is sent before the connection is terminated. The release is accomplished in a three-way handshake between client and server processes. The connection-oriented protocols in the OSI protocol suite, on the other hand, do not support orderly release. Applications perform any handshake necessary for ensuring orderly release.
Examples of services that use connection-oriented transport services are telnet, rlogin, and ftp.
Refer to the exhibit.
If the hubs in the graphic were replaced by switches, what would be virtually eliminated?
A. broadcast domains
B. repeater domains
C. Ethernet collisions
D. signal amplification
E. Ethernet broadcasts
Modern wired networks use a network switch to eliminate collisions. By connecting each device directly to a port on the switch, either each port on a switch becomes its own collision domain (in the case of half duplex links) or the possibility of collisions is eliminated entirely in the case of full duplex links.
New Updated 100-105 Exam Questions 100-105 PDF dumps 100-105 practice exam dumps: https://www.dumpsschool.com/100-105-exam-dumps.html